Free Cisco CCNA, CCENT, CCNP Certification Tutorial

Routing

Routing is a relay system by which packets are forwarded from one device to another. Each device in the network as well as the network itself has a logical address so it can be identified and reached individually or as part of a larger group of devices. For a router to act as an effective relay device, it must be able to understand the logical topology of the network and to communicate with its neighboring devices.

The router understands several different logical addressing schemes and regularly exchanges topology information with other devices in the network. The mechanism of learning and maintaining awareness of the network topology is considered to be the routing function while the movement of traffic through the router is a separate function and is considered to be the switching function. Routing devices must perform both a routing and a switching function to be an effective relay device. A router receiving a packet from a host, the router will need to make a routing decision based on the protocol in use; the existence of the destination network address in its routing table; and the interface that is connected to the destination network. After the decision has been made the router will switch the packet to the appropriate interface on the router to forward it out. If the destination logical network does not exist in the routing table, routing devices will discard the packet and to generate an Internet Control Message Protocol (ICMP) message to notify the sender of the event.

Routing Table

A routing table is a database repository that holds the router's routing information that represents each possible logical destination network that is known to the router. The entries for major networks are listed in ascending order and, most commonly, within each major network the sub networks are listed in descending order. If the routing table entry points to an IP address, the router will perform a recursive lookup on that next-hop address until the router finds an interface to use. The router will switch the packet to the outbound interfaces buffer. The router will then determine the Layer 2 address that maps to the Layer 3 address. The packet will then be encapsulated in a Layer 2 frame appropriate for the type of encapsulation used by the outbound interface. The outbound interface will then place the packet on the medium and forward it to the next hop. The packet will continue this process until it reaches its destination. There are two ways in which a routing table can be populated: a route can be entered manually, this is called static routing, or routers can dynamically learning a route. Once a router learns a route, it is added to its route table.

Listed below are more articles related to the above article from the "Certification Test Exam" article category.

People interested in the above article "Free Cisco CCNA, CCENT, CCNP Certification Tutorial" are also interested in the related articles listed below:

What You Should Know About SAP Certification

There are very few Certification credentials in the business world, which carry the same value and prestige as SAP Certification. If you wish to achieve SAP Certification, you have to hone your skills, either through rigorous study or direct industry experience.

CompTIA A+, Network+ Certification Tutorial - Function of Network Hubs

A hub is a device used to connect all of the computers on a star or ring network. A hub is nothing more than a box with a series of cable connectors in it. Hubs are available four- and five-port devices designed for home and small business networks to large rack-mounted units with up to 24 ports or more. Installing a single hub is simply a matter of connecting it to a power source and plugging in cables connected to the network interface adapters in your computers.

CompTIA A+, Security+, Network+ Tutorial – Ethernet Card Troubleshooting

When a computer fails to communicate, the network interface adapter can be at fault, but it is far more likely that some other component is causing the problem. Before you see to the network interface adapter, check for the following problems first.

CCNA, CCENT, CCNP Tutorial on Routers and Routing

Routers are the critical part of all the networks and can be both security aid and security vulnerability. A router basically has more network interfaces through which network traffic is forwarded. Or it might be blocked. The router decides when to forward packets between the networks based on internal routing table.

Free CCNA tutorial about Cisco IOS Software, Cisco Router Configuration modes and Cisco CLI (Command Line Interface)

Which ever method you use, you enter user exec mode first. User exec mode is one of three command exec modes in the IOS user interface. Enable mode, also known as privileged mode or Privileged exec mode, and command mode are the others.

Free Cisco CCNA Tutorial

All routers attempt all four steps each time that the router is powered on or reloaded. The POST code and functions cannot be changed by the router administrator.

Why should you avoid getting a Braindump Certification?

Generally speaking, Braindumps refers to lists of questions and answers from an actual IT certification exam. This dangerous, illegal and unethical trend is like a plague to IT profession as well as industry.