Tips, Hints, For Transmission Cooler installations

Many of you add aftermarket coolers to your cars and this is allways a good idea. Here are some hints.

1. Allways mount the cooler in a place that has good air flow and if mounting in front of the radiator always make sure the fin's in the cooler are parallel with the fin's in the radiator to avoid restricting air flow to the radiator. If you must place the cooler in and area with little air flow a FAN is a must.

2. When Installing coolers make sure lines are clear of anything that can rub them and always use line that’s approved for transmission/hydraulic fluid. Fuel line will not work and will break down in transmission fluid.

3. By passing the radiator is the way I prefer a cooler be set up. Generally the transmission will run cooler this way and additionally this may take some of the load off the radiators job of cooling the engine.

4. When hooking up multiple coolers several things should be noted. The cooler itself is a restriction of flow and this restriction while not a problem for the cooling or lube to the trans can cause excessive pressure inside the converter. This can force the converter against the flex plate more so than normal and cause wear to the engine thrust bearing. A stopped up or severely restricted cooler or cooler lines can do the same. So when installing more than one cooler its advised to put them in parallel with each other, This means one line from the trans is split with a Y and one line run to each cooler then out of each and into a Y back to a single line running to the trans. This will assure adequate cooling while reducing the wear to the engine thrust bearing. Always use line that’s at least as large as the inlets in the cooler, Avoid extreme twist or turns in them particularly with rubber lines.

5. Type and brands of coolers; I really have no preference here as far as brand. From my experience and expensive brand name or a generic unit appear to do the same job. I have found the stacked plate (Flat tube) Types when measured inlet to outlet temp drop tend to be more efficient in the same dimensional sizes with a greater temperature drop. I did a test once with two coolers in parallel one round tube and one flat with a laser thermometer to determine this.

6. This is not specifically about a cooler but about cooling. Always be sure that the metal lines coming from the transmission under car do not contact the headers or exhaust. I once had a car where the transmission temps would sky rocket when the car was being run hard and couldn’t understand why. I after some looking around found that the cooler lines in and out were pinned against the headers. This would super heat the fluid when the headers got hot. Moved them away and the problem was solved, So always keep trans cooler lines factory or otherwise as far away from the exhaust as possible.

7. Trans temps - This question gets ask a lot. What’s TOO HOT? Well ideally you want you average temp to stay under 190 degrees however I would not get to concerned till the temps get at and or over 230 degrees. Heat can damage a trans but with the exception of extreme heat 250 or higher this damage is a long term killer by breaking down fluid and causing rubber seals to harden and break.

8. Never use your cooler lines to remove fluid from your transmission by starting the engine or in and attempt to flush by catching fluid in a pan while adding fluid to the dipstick. When this is done no lube is being sent to the planets and bushings and they can go dry and melt down very quickly destroying or significantly shortening the life of your transmission.

9. It is advisable to fully and properly flush a cooler especially when a converter failure is involved. Where a transmission internal failure is unlikely to put debris in the cooler since all fluid coming from transmission must travel through the trans filter. The fluid coming from the Pump or converter does not and any debris from these will certainly end up in the cooler. Its always a good idea to power flush a cooler or replace after a failure but is particularly important in the case of this type failure. Anything that’s in your cooler or lines will end up in your Valve Body, Bushings and Planets. A cooler cannot be properly cleaned simply by blowing air through it. A can of cooler flush which most transmission shops and or transmission parts suppliers should have followed by a blow out with air is the correct way to do it.

10. When installing rubber cooler lines to metal lines it’s a good idea to put a small flair at the end of the metal line. Not too big because you will tear the line on the inside during install. Then place a clamp just ahead of the flair. Also roughening up the outer surface of the metal line with very coarse sand paper in area where clamp will ride will help assure a good seal and reduce the possibility of blow off. Never over tighten clamps to the point of the rubber oozing through or being cut this will cause a failure too.

11. Temp sending units- The best place for these is in the pan since that will give the best average temperature which is what’s important, using the pressure port is ok however you will show temps 10 to 20 degrees higher average than you would in the pan. I do not suggest placing temp senders in either the inlet or outlet from the cooler as they will increase cooler restriction and increase the odds of a leak.

Listed below are more articles related to the above article from the "Automotives" article category.

People interested in the above article "Tips, Hints, For Transmission Cooler installations" are also interested in the related articles listed below:

Outstanding Service Is The Baltimore Chevrolet Way

In this day and age, many businesses continue to employ advertising gimmicks that do not provide accurate information to the customer. Instead, this misleading advertisement tends to lead the customer astray and fool them into purchases of little use to them. Vehicle dealerships have been known to employ such tactics in the past, but there are still a multitude of ethical businesses that would not compromise their values to earn profit.

Dry Flow Cold Air Intakes

There are several types of cold air intakes on the market today. Most of which people call K&N no matter who makes the kit. Today we aren't going to talk about the standard oiled K&N type air filter. We are going to talk about dry flow filters and their differences from the standard oiled filters on the market today. We are going to talk about the AEM brand dryflow filters, and the AFE brand Pro Dry S filters.

Airaid Diesel Intakes Vs Volant Diesel Intakes

In an effort to get a little bit more knowledge out there about the diesel aftermarket we are going to do a quick comparison on the Airaid diesel intake kits and the Volant diesel intake kits that are on the market. There are so many different types of what seems to be the same thing out in the market that it's easy to get confused and not be able to tell the difference between two items or if there are any differences at all.

Purchasing a Lifetime Warranty Can Relieve a Driver's Hassles

Even quality, reliable vehicles can succumb to poor weather, rough roads or highways, accidents, reckless driving and various other external elements that can wreak havoc on a car’s condition. However, these problems can be easily alleviated if you purchase the correct auto lifetime warranty. Lifetime warranties can cover a myriad of car accidents, manufacturing errors, dents, scratches and maintenance repairs.

How to Personalize your Vehicle and Protect its Resale Value

As we get older, time becomes more and more precious. Between having a career, a family, kids, and stacks of bills to pay, it becomes hard to find the time to dedicate towards our passions in life; surfing, snowboarding, skiing, fishing, hiking, mountain biking, 4-wheeling, off-roading, dirt biking... this list can go on and on.

How Does Actuators Works?

In actuator valve engineering and design, it is essential for engineers, designers, and manufacturers to fully understand the aspects and processes of using this particular product that would eventually help build effective engineering designs in a safe and efficient manner. One of the most significant products of the company would be the actuators. To make this technical term simpler, an actuator is a device that transforms or converts energy into motion.

Are Hybrid Vehicles Safe?

The cost of living is on the rise, and oil prices are hitting record levels. People are more than careful these days how they operate their vehicles because of gas prices. These challenges have caused many people to look at the growing trend of driving hybrid vehicles. However, are hybrid vehicles safe? Hybrid vehicles have proven to be as safe as gasoline-powered vehicles. The crash specifications are the same as those of normal cars. Hybrids also have the same restraint and airbag systems installed.